Base system

This chapter describes all available modules at the end of installation. All modules outside this section must be installed from Software center, including backup and users support.


The Dashboard page is the landing page after a successful login. The page will display the status and configurations of the system.

Disk analyzer

This tool is used to visualize disk usage in a simply and nice graph in which you can interact with click and double click to navigate in the directories tree.

After installation go in Dashboard and then Disk usage tab and click Update to index the root directory and to display the graph. This process can take several minutes depending on occupied disk space.

Well known folders are:

  • Shared folders: /var/lib/nethserver/ibay
  • User home directories: /var/lib/nethserver/home
  • Windows roaming profiles: /var/lib/nethserver/profile
  • Mail: /var/lib/nethserver/vmail
  • Faxes: /var/lib/nethserver/fax
  • MySQL databases: /var/lib/mysql


The Network page configures how the server is connected to the local network (LAN) or other ones (i.e. Internet).

If the server has firewall and gateway functionality, it will handle extra networks with special function like DMZ (DeMilitarized Zone) and guests network.

NethServer supports an unlimited number of network interfaces. Any network managed by the system must follow these rules:

  • networks must be physically separated (multiple networks can’t be connected to the same switch/hub)
  • networks must be logically separated: each network must have different addresses
  • private networks, like LANs, must follow address’s convention from RFC1918 document. See Address for private networks (RFC1918)

Every network interface has a specific role which determinates its behavior. Roles are identified by colors. Each role correspond to a well-known zone with special network traffic rules:

  • green: local network. Hosts on this network can access any other configured network
  • blue: guests network. Hosts on this network can access orange and red network, but can’t access to green zone
  • orange: DMZ network. Hosts on this network can access red networks, but can’t access to blue, orange and green zones
  • red: public network. Hosts on this network can access only the server itself

See Policy for more information on roles and firewall rules.


The server must have at least one network interface. When the server has only one interface, this interface must have green role.

If the server is installed on a public VPS (Virtual Private Server) public, it should must be configured with a green interface. All critical services should be closed using Network services panel.

Logical interfaces

In Network page press New interface button to create a logical interface. Supported logical interfaces are:

  • alias: associate more than one IP address to an existing network interface. The alias has the same role of its associated physical interface
  • bond: arrange two or more network interfaces, provides load balancing and fault tolerance
  • bridge: connect two different networks, it’s often used for bridged VPN and virtual machine
  • VLAN (Virtual Local Area Network): create two or more logically separated networks using a single interface
  • PPPoE (Point-to-Point Protocol over Ethernet): connect to Internet through a DSL modem

Aliases are used to configure multiple IPs on a single NIC. For example, if you want to have more public IP on a red interface.

Bonds allow you to aggregate bandwidth between two or more network interfaces. The system will use all network interfaces at the same time, balancing traffic among all active interfaces. If an error occurs, the faulty card is automatically excluded from the bond.

A bridge has the function to connect different network segments, for example by allowing virtual machines, or client connected using a VPN, to access to the local network (green).

When it is not possible to physically separate two different networks, you can use a tagged VLAN. The traffic of the two networks can be transmitted on the same cable, but it will be handled as if it were sent and received on separate network cards. The use of VLAN, requires properly configured switches.


The PPPoE logical interface must be assigned the red role, thus requires the gateway functionality. See Firewall and gateway for details.

Address for private networks (RFC1918)

TCP/IP private networks not directly connected to Internet should use special addresses selected by Internet Assigned Numbers Authority (IANA).

Private network Subnet mask IP addresses interval - - -

Network services

A network service is a service running on the firewall itself.

These services are always available to hosts on green network (local network). Access policies can be modified from Network services page.

Available policies are:

  • Access only from green networks (private): all hosts from green networks and from VPNs
  • Access from green and red networks (public): any host from green networks, VPNs and external networks. But not guests (blue) and DMZ (orange) networks
  • Access only from the server itself (none): no host can connect to selected service

Custom access

If selected policy is private or public, it’s possible to add hosts and networks which are always allowed (or blocked) using Allow hosts and Deny hosts. This rule also apply for blue and orange networks.


Given the following configuration:

  • Orange network:
  • Access for NTP server set to private

If hosts from DMZ must access NTP server, add network inside the Allow hosts field.

Trusted networks

Trusted networks are special networks (local, VPNs or remote) allowed to access special server’s services.

For example, hosts inside trusted networks can access to:

  • Server Manager
  • Shared folders (SAMBA)

If the remote network is reachable using a router, remember to add a static route inside Static routes page.

Static routes

This page allow to create special static routes which will use the specified gateway. These routes are usually used to connect private network.

Remember to add the network to Trusted networks, if you wish to allow remote hosts to access local services.

Organization contacts

The Organization contacts page fields are used as default values for user accounts. The organization name and address are also displayed on the Server Manager login screen.

Server certificate

The Server certificate page shows the currently installed SSL certificate that is provided by all system services.

The Generate certificate button allows generating a new self-signed SSL certificate. When a new certificate is generated, all SSL services are restarted and network clients will be required to accept the new certificate.


To avoid problems while importing the certificate in Internet Explorer, the Common Name (CN) field should match the server FQDN.

Install a custom certificate

Custom certificates should be placed inside the following standard directories:

  • /etc/pki/tls/certs: public key
  • /etc/pki/tls/private: private key

Set the private key and certificate file paths:

db configuration setprop pki CrtFile '/path/to/cert/pem-formatted.crt'
db configuration setprop pki KeyFile '/path/to/private/pem-formatted.key'

You can also set a SSL certificate chain file:

db configuration setprop pki ChainFile '/path/to/cert/pem-formatted-chain.crt'

Notify registered daemons about certificate update:

signal-event certificate-update

Custom certificate backup

Always remember to add custom certificates to configuration backup. Just add the paths inside /etc/backup-config.d/custom.include file.

For example, if the certificate is /etc/pki/tls/certs/mycert.crt, simply execute:

echo "/etc/pki/tls/certs/mycert.crt" >> /etc/backup-config.d/custom.include

Change user password

All users can login to Server Manager using their own credentials and accedd the user profile.

After login, a user can change the password and information about the account, like:

  • Name and surname
  • External mail address

The user can also overwrite fields set by the administrator:

  • Company
  • Office
  • Address
  • City


The machine where NethServer is installed can be rebooted or halted from the Shutdown page. Choose an option (reboot or halt) then click on submit button.

Always use this module to avoid bad shutdown which can cause data damages.

Log viewer

All services will save operations inside files called logs. The log analysis is the main tool to find and resolve problems. To analyze log files click in Log viewer.

This module allows to:

  • start search on all server’s logs
  • display a single log
  • follow the content of a log in real time

Date and time

After installation, make sure the server is configured with the correct timezone. The machine clock can be configured manually or automatically using public NTP servers (preferred).

The machine clock is very important in many protocols. To avoid problems, all hosts in LAN can be configured to use the server as NTP server.

Inline help

All packages inside the Server Manager contain an inline help. The inline help explains how the module works and all available options.

These help pages are available in all Server Manager’s languages.

A list of all available inline help pages can be found at the address:



If the server has address, and you want to see all English help pages, use this address: