Installation

Minimum requirements

Minimum requirements are:

  • 64 bit CPU (x86_64)
  • 1 GB of RAM
  • 8 GB of disk space

Hint

We recommend to use at least 2 disks to setup a RAID 1. The RAID software will ensure data integrity in case of a disk failure.

Hardware compatibility

NethServer is compatible with any hardware certified by Red Hat® Enterprise Linux® (RHEL®), listed on hardware.redhat.com

Installation types

NethServer supports two installation modes. In short:

Installing from ISO

  • Download the ISO image
  • Prepare a CD / DVD
  • Follow the wizard

Installing from YUM

  • Install CentOS Minimal
  • Configure the network
  • Install from network

Installing from ISO

Warning

The ISO installation will erase all existing data on hard drives!

Download the ISO file from official site www.nethserver.org. The downloaded ISO file can be used to create a bootable media such as CD or DVD. The creation of a bootable disk is different from writing files into CD/DVD, and it requires the use of a dedicated function (e.g. write or burn ISO image). Instructions on how to create a bootable CD/DVD from the ISO are easily available on the Internet or in the documentation of your operating system.

Start the machine using the freshly backed media. If the machine will not start from the CD/DVD, please refer to the documentation of the motherboard BIOS. A typical problem is how boot device priority is configured. First boot device should be the CD/DVD reader.

On start a menu will display different types of installation:

NethServer interactive install

It allows you to select the language, configure RAID support, network, and encrypted file system. It will be described in depth in the next paragraph.

Other / Unattended NethServer install

This installation mode does not require any kind of human intervention: a set of default parameters will be applied to the system.

Standard CentOS installations

Use the standard CentOS installation procedure.

Tools

Start the system in rescue (recovery) mode, execute a memory test or start the hardware detection tool.

Boot from local drive

Attempts to boot a system that is already installed on the hard disk.

At the end of the installation process you will be asked to reboot the machine. Be sure to remove the installation media before restarting.

Unattended mode

After installation, the system will be configured as follows:

  • User name: root
  • Default password: Nethesis,1234
  • Network: DHCP enabled on all interfaces
  • Keyboard: en
  • Time zone: Greenwich
  • Language: English
  • Disks: if there are two or more disks, a RAID 1 will be created on first two disks

Install options

You can add extra parameters to unattended installation by pressing TAB and editing the boot loader command line.

To disable raid, just add this option to the command line:

raid=none

If you need to select installation hard drives, use:

disks=sdx,sdy

Other available options:

  • lang: system language, default is en_US
  • keyboard: keyboard layout, default is us
  • timezone: default is UTC Greenwich
  • fspassword: enable file system encryption with given password This option can be used even in Interactive Mode

Interactive Mode

The interactive mode allows you to make a few simple choices on the system configuration:

  • Language
  • Software RAID
  • Network configuration

Language

Select the language in which you want to use the interactive mode. Keyboard layout and time zone are changed accordingly and can be modified just after the first login to the web interface.

System language is always set to English.

Software RAID

RAID (Redundant Array of Independent Disks) allows you to combine all the disks in order to achieve fault tolerance and an increase in performance.

This screen is displayed when two or more disks were detected at start.

Available levels:

  • RAID 1: it creates an exact copy (mirror) of all the data on two or more disks. Minimum number of disks: 2
  • RAID 5: it uses a subdivision of the data at the block level, distributing the parity data evenly across all disks. Minimum number of disks: 3
Spare disk

You can create a spare disk if disk number is greater than the minimum required by the selected level RAID, A spare disk will be added to the RAID in case a failure occurs.

System administrator password

You can change the root user’s password inside the first configuration wizard.

A good password is:

  • at least 8 characters long
  • contain uppercase and lowercase letters
  • contain symbols and numbers

Default password is Nethesis,1234.

Encrypted file system

When enabling this option, all data written to the disk will be encrypted using symmetric encryption. In case of theft, an attacker will not be able to read the data without the encryption key.

It is possible to choose a password for the encryption, otherwise the system administrator password will be used.

Note

You will need to enter the password at every system boot.

Warning

Following characters are not supported inside the password: #, = and $.

Network interfaces

Select the network interface that will be used to access the LAN. This interface is also known as green interface.

Network configuration

Host and Domain Name (FQDN)

Type the host name and domain in which the server will operate (e.g. server.mycompany.com).

Note: Domain name can only contain letters, numbers and the
dash.

IP Address

Type a private IP address (from RFC 1918) to be assigned to the server; if you want to install it in an existing network, you must provide a unused IP address valid for that network (in general you can use the first or last host inside the network range, e.g. 192.168.7.1 or 192.168.7.254).

Netmask

Type the subnet mask of the network. You can safely leave the default value.

Gateway

Type the IP address of the gateway on which you are installing the server.

DNS

Type a valid DNS. Example: 8.8.8.8

End of installation procedure

After parameters input, the procedure will start the installation. See also Next steps.

Install on CentOS

It is possible to install NethServer on a fresh CentOS installation using the yum command to download software packages. This is the recommended installation method if you have

  • a virtual private server (VPS), or
  • an USB stick.

For example, if you wish to install NethServer 6.9, just start with a CentOS 6.9 on your system (many VPS providers offer CentOS pre-installed virtual machines), and then execute below commands to transform CentOS into NethServer.

Enable specific YUM repositories with this command:

yum localinstall -y http://mirror.nethserver.org/nethserver/nethserver-release-6.rpm

To install the base system, run:

nethserver-install

Alternatively, to install base system and additional modules, pass the name of the module as a parameter to the install script. Example:

nethserver-install nethserver-mail nethserver-nut

Next steps

At the end of the installation procedure, access the server-manager to install additional software.